Updated: Feb 14, 2026
Location and Projects
Address
114 9TH ST NE, Chisholm, MN, 55719
Use our bidding system to
request a quote
Ampedup Electrician
Ampedup LLC, 114-9 Th St NE, Chisholm, MN holds a Electrical license according to the Minnesota license board.
Their BuildZoom score of 96 ranks in the top 20% of 77,973 Minnesota licensed contractors.
Their license was verified as active when we last checked. If you are thinking of hiring Ampedup LLC, we recommend double-checking their license status with the license board and using our project planner to get competitive quotes.
Ampedup LLC Contact Information
Phone Number: (218) 969-6141
Edit
Address: 114 9TH ST NE, Chisholm, MN 55719
Edit
Do you work for this business? Unlock this free profile to update company info and see who's viewing your profile.
This is a sample of this contractor's permits. Click here to access their complete permit history.
Installed a sub panel because the main panel could not addition the new style afci/gfci breakers. added and corrected wiring done 20 years ago. troubleshooting and correcting problems all over the place. added an air conditioning circuit and a mini split circuit outside in disconnects and fed from the dual fuel panel. added wiring in the main addition area
Valuation:
N/A
Permit #:
ELE2505-05705
Status:
issued
Fee:
$106
Permit Type:
One-family dwelling
Building Type:
N/A
The kitchen was taken out and some circuits were moved around and added. the mechanical room had more circuits added and a circuit was added in the main level bathroom for a towel dryer. the pole barn on the existing side that was unheated is getting insulated and wired in mc cable then getting sheeted with outdoor metal siding new circuits added an old wiring re-located
Valuation:
N/A
Permit #:
ELE2505-05704
Status:
issued
Fee:
$71
Permit Type:
One-family dwelling
Building Type:
N/A
A small mother in-law house is being built next to the existing house on the property. a 200a outside panel with main disconnect will be installed on the exterior of the house and a 100a sub panel will be installed inside the house. house will be wired by ampedup
Valuation:
N/A
Permit #:
ELE2409-07264
Status:
final
Fee:
$171
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a 200a automatic transfer switch and wired in a generator. the service at this house is designated at the pole supplied by the power company its a panel with breaker spaces. the house was fed with a four wire feed and the equipment grounds and neutrals are separated. the transfer switch was also wired with 4-wire and equipment grounds and neutral is separated
Valuation:
N/A
Permit #:
ELE2502-00184
Status:
final
Fee:
$36
Permit Type:
One-family dwelling
Building Type:
N/A
An existing garage wired in emt addition a small living area built in the second level like a bonus truss section. a bathroom dining room and living room are added. 3 more circuits were added in emt as well. a well pump circuit outside receptacle circuit and lighting circuit. 10 circuits added in total the garage is across the street from the address. its all considered the same fire ... see more
Valuation:
N/A
Permit #:
ELE2408-11654
Status:
final
Fee:
$71
Permit Type:
One-family dwelling
Building Type:
N/A
In order to correct a poorly installed garage feed the utility company needs to remove the old meter base and install a new one. the house and garage will be connected into it and the garage service will be installed properly
Valuation:
N/A
Permit #:
ELE2408-01643
Status:
final
Fee:
$48
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a 200a meter base combo panel outside as the main service. installed a 200a sub panel inside the house. the house and garage have been re-wired and all old wiring removed. the door code is #8910. ready for a rough in
Valuation:
N/A
Permit #:
ELE2405-06948
Status:
final
Fee:
$171
Permit Type:
One-family dwelling
Building Type:
N/A
There was an existing garage that was taken down and a new garage built in its place. the old feed was re-trenched in from the house and installed in a new 30a 240v sub panel. the garage was wired with 4 circuits
Valuation:
N/A
Permit #:
ELE2411-02309
Status:
final
Fee:
$62
Permit Type:
One-family dwelling
Building Type:
N/A
A hot tub addition was added about 7 years ago. the hot tub was removed and some receptacles were added with the sheetrock removed at about 3 around the addition. 2 receptacle locations were added and inspected but covered up for future when the hot tub was to be removed. the old conduit that fed the hot tub was redirected into a receptacle box and was used to pull in the new wire. ne... see more
Valuation:
N/A
Permit #:
ELE2406-06431
Status:
final
Fee:
$71
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a 20a circuit for a sump pump. the circuit is on a standard breaker and a 4-square box is nippled off the panel. an afci/gfci receptacle was installed in the box. then a receptacle was fished in the wall with nm cable and a standard receptacle fed from the load side of the afci/gfci the door code is 2866
Valuation:
N/A
Permit #:
ELE2407-03548
Status:
final
Fee:
$36
Permit Type:
One-family dwelling
Building Type:
N/A
The garage had some bad wiring feeding an old outside light. the wiring was fixed and extended in emt. extended a circuit in the house in the living room with wiremold. all circuits were already protected with afci/gfci breakers. wired the unit heater in the garage with a new mc whip. installed a disconnect for the ev charger and put the wires in emt that were in flex. the circuit was... see more
Valuation:
N/A
Permit #:
ELE2408-13332
Status:
final
Fee:
$36
Permit Type:
One-family dwelling
Building Type:
N/A
On one 40a- 240v feed from the house two sub panels were installed in the yard. the sub panels have 2 receptacle circuits from one and one receptacle circuit on the other. i have pictures of the trench if needed. the trench is at least 30 deep and 240 long. i used 2/2/4 with ground aluminum sec. two ground rods were installed at each location and there is a 40a disconnect breaker at e... see more
Valuation:
N/A
Permit #:
ELE2411-06264
Status:
final
Fee:
$60
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a new 200a outdoor electrical service meter base combo and sub fed the existing panel. the water meter ground is in the new service and all the neutrals and grounds were separated. another sub panel was installed in the new addition. the addition is a garage living room bedroom office and bathroom
Valuation:
N/A
Permit #:
ELE2407-10479
Status:
final
Fee:
$206
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a 3/4 emt conduit to feed a new equipment dryer that is 3-phase 208v 35a. wired with #8 thhn 4-wire with ground. fed from panel 2mp2 - circuits 29 31 33. dryer is in room 140 fire decon room
Valuation:
N/A
Permit #:
ELE2505-01779
Status:
final
Fee:
$36
Permit Type:
Non-dwelling
Building Type:
N/A
Installed a small 100a rated panel in a garage and wired the garage in nm cable. the feed came from the main service panel outside the house and is fed from a 30a 2-pole breaker #10/3 uf
Valuation:
N/A
Permit #:
ELE2505-07385
Status:
final
Fee:
$60
Permit Type:
One-family dwelling
Building Type:
N/A
A bedroom and bathroom are being turned into a large bathroom. some wires were eliminated and new wiring added. i put two junction boxes in the attic to relocate the circuits
Valuation:
N/A
Permit #:
ELE2409-03755
Status:
final
Fee:
$71
Permit Type:
One-family dwelling
Building Type:
N/A
Installing a new 30a 240v gfci protected dryer receptacle and one 20a afci/gfci laundry receptacle surface in emt and mc the dryer nm was reused from its old location
Valuation:
N/A
Permit #:
ELE2504-00725
Status:
final
Fee:
$36
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a 15a circuit for a dishwasher. an access hole was installed to unplug the dishwasher. the circuit is protected by a 15a breaker and it’s on the load side of an afci/gfci receptacle at the panel
Valuation:
N/A
Permit #:
ELE2507-06516
Status:
final
Fee:
$36
Permit Type:
One-family dwelling
Building Type:
N/A
Installed a new circuit for the bathroom heat - on the new fan/light. added a light in the shower area. everything was fished in the walls. emt was ran from the back of the panel in the mechanical room into the attic for the new circuit and has a 4 square box in the attic switching over to nm from there. afci/gfci breaker
Valuation:
N/A
Permit #:
ELE2412-03155
Status:
final
Fee:
$36
Permit Type:
One-family dwelling
Building Type:
N/A
The kitchen is getting remodeled and circuits moved around. the old ranges were fed from a double tapped 100a service. i added a 100a rated 8 space panel above that single breaker and pulled the old wire out. installed one cook top circuit one double oven circuit one fridge circuit and one microwave circuit. the wall is concrete and i ran surface mount emt and its being furred out to 1.5
Valuation:
N/A
Permit #:
ELE2405-10595
Status:
final
Fee:
$71
Permit Type:
Non-dwelling
Building Type:
N/A
Similar Contractors See more
License # EA003651
Saginaw, MN
110
BZ Score
$18.9M
Avg Project
-
Projects
109
BZ Score
-
Avg Project
-
Projects
110
BZ Score
$10K
Avg Project
-
Projects
Ampedup LLC Reviews
BuildZoom hasn't received any reviews for Ampedup LLC. Click here to be alerted when reviews are posted about them.
Recent Buildzoom Projects
Verified License
BuildZoom confirmed this contractor's license
Ampedup LLC License info
Verified License
| License # | EA726185 |
| Status | Active |
| State | Minnesota |
| Type | Electrical |
- BuildZoom verified this license was active as of February 2026.
Verify this license's status for Ampedup LLC at the Minnesota Department of Labor & Industry.
This is a sample of licensing data; click here to access a complete history.
96
BuildZoom Score
258
Permits
- Building permit records show that Ampedup LLC has worked on 258 permitted projects.