1 200a serv for install new meter in pge specified location [wo#m3322300]. remove old meter main and replace with ug 204 meter base (spec'd by pge). inspect and possibly replace existing grounding electrode system per scope request. re-install existing riser conduit. install new 8/16 exterior panel with pass through lugs. re-route existing 4wire cabling to new exterior panel and termi... see more

Install new 200 amp meter socket and adjacent 200/200 disconnect. [pge work order #m3275161] --20 to 25 to the right of existing location. photovoltaic interconnection to be supply side tap performed by others. inspect & possibly replace existing g.e.s. per scope request. install new 4wire ser cable per nec to new interior load center {200/200}. new exterior conduit to follow line set... see more

Replace existing m.p. install new 225/150 amp surface/flush mount main distribution panel. ensure existing g.e.s. of panel is up to code standards photovoltaic to be 2pole 30amp. re-use existing feeder wire from meter no meter replacement is necessary

Replace existing m.p. install new 200/200 or 200/150 amp surface/flush mount main distribution panel. ensure existing g.e.s. of panel is up to code standards photovoltaic to be 2pole 30amp. re-use existing feeder wire from meter no meter replacement is necessary. install code compliant main breaker in conjunction with existing wire from the meter

Sub-panel insert addition in new 125 amp mlo sub-panel adjacent to existing panel install 80 amp breaker & wiring (#4awg/3) in exiting square d panel to new subpanel -- relocate 20/30 quad/50a/2p/fix double lugged -15 -- shift one load to new sub. photovoltaic interconnection performed by others (supply side tap in existing panel). separate g & n in subpanel

1 200a serv for enforce 6-handle rule with existing interior panel addition in new 125amp sub-panel on adjacent wall traveling 11 down the wall to avoid dryer ducting that is installed on the garage stem wall. including wiring from a 2-pole 60 in existing panel to energize new sub-panel. relocate single pole loads into new sub-panel to ensure a two hand throw rule in original panel. i... see more

1. install (1) new exterior 125amp load center surface mount on exterior face of home in ion appointed location. install (1) new mast (1 grc with roof jack & boot) from this panel to penetrate through the eve of the roof and extend 2 above the roof line with weather-head included. install #6awg in this mast and splice onto 12 of #6awg triplex that extends from the home to adjacent bui... see more

2 200a 6 400a and 259 bc for remodel of existing space with plan review

1 200a serv for install new 200amp meter socket in specified pge location {m3028154}. install new wiring from meter socket to existing interior load center (back to back w/meter) inspect and possibly replace existing g.e.s per scope request. new ser cabling from meter to house panel to be 200amp rated. new mast to 16 with guying kit. full service upgrade

Install new 200/200 mm combo. [pge work order# m3278930 ] --new location right of existing meter base. photovoltaic interconnection to be 20 amp 2pole installed in new interior load center. inspect & possibly replace existing g.e.s. per scope request. install new 4wire ser cable per nec to new interior load center {200/200}. new mast to 14/16 w/guy kit and new wiring

Install new 200/150 amp main disconnect enclosure on the exterior of the home roughly 25 from the existing meter location near the man door of the garage. install 1.5 pvc conduit from existing meter to new disconnect with code compliant wiring from meter to new exterior disconnect. inspect and possibly replace existing g.e.s per scope request. new 4c cabling from disconnect to house p... see more

Enforce 6-handle rule with existing interior panel addition in new 100amp sub-panel adjacent or below existing panel. including wiring from a 2-pole 60 in existing panel to energize new sub-panel. relocate single pole loads into new sub-panel to ensure a two hand throw rule in original panel. isolate g & n's in subpanel. relocate and arrange breakers as necessary to ensure code compli... see more

1 200a serv for replace existing electrical panel with new 125 amp flush/recessed mount distribution panel. procure and install all necessary equipment. inspect and replace existing g.e.s. per nec. full service upgrade. -- utilize a larger siemens panel as circuit capacity is full. install new disconnect on exterior of home adjacent to meter this is a code requirement as panel is too ... see more

1. replace existing stablok m.p. install new 125/125 amp surface/flush mount main distribution panel. ensure existing g.e.s. of panel is up to code standards photovoltaic to be 2pole 25amp. install new 4 wire from 125/125 amp disco listed on bullet point #2 to new interior panel. 2. re-route existing feeder from old panel to new exterior 125amp disconnect with provisions mounted just ... see more

1 200 a serv for replace existing main distribution panel (main lug). install new 200/150 amp surface/flush mount main distribution panel. ensure existing grounding of panel is up to code standards photovoltaic interconnection line side to be performed by others. install new feeder if necessary

Replace existing main distribution panel. install new surface/flush mount main distribution panel. ensure existing grounding of panel is up to code standards. we will re-use the feeder from the current meter for new main distribution panel. ensure ample circuit capacity for ev charger & dishwasher circuitry

-- install new 125a surface mount meter socket and new separate 125 flush mount main distribution panel -- install new grounding electrode system. -- overhead service: upgrade weather head and riser. -- interconnect photovoltaic with a supply side tap. -- replace meter with new 125a meter socket and feed new exterior 125a main disconnect enclosure. -- upgrade interior panel to new 125... see more

(1) 200 amp svc and 3 bc's for replace existing main distribution panel. install new 200/200 amp surface/flush mount main distribution panel. ensure existing grounding of panel is up to code standards. install new feeder from the existing meter to the new panel

Install new 200 amp meter base and new 200/200 exterior main distribution panel-->will need 8/16 panel as cad is an exterior line side photovoltaic interconnection & there is a circuit that needs to be installed from the existing meter main

Replace existing main distribution panel. install new 200/200 amp surface/flush mount main distribution panel. ensure existing grounding of panel is up to code standards photovoltaic interconnection to be line side tap coordinated by others